BMC - RLM - SP

BMC - RLM - SP
 
 
BMC - RLM - SP is console port to connect the filer,
  1. BMC - RLM - SP is a separate device in the FAS chassis.
  2. It has it's own IP and is independent of the FAS so it keeps running any time.
  3. BMC - RLM - SP is connects to the motherboard and install separately.When a FAS fails over BMC - RLM - SP keeps working locally.
  4. These provide remote support like remote access, monitoring and troubleshooting.
Before FAS 2xxx they called BMC
FAS 2xxx to FAS 30xx / 31xx they called RLM

After FAS 3240 and 3270  they named SP (service processor)



BMC : Baseboard Management Controller

RLM : Remote Lan Module

SP : Service Processor

Comments

Post a Comment

Popular posts from this blog

Netapp Cluster mode commands cheat sheet

Netapp Cluster mode commands cheat sheet Netapp Cluster mode commands cheat sheet set -privilege advanced (Enter into privilege mode) set -privilege diagnostic (Enter into diagnostic mode) set -privilege admin (Enter into admin mode) system timeout modify 30 (Sets system timeout to 30 minutes) system node run – node local sysconfig -a (Run sysconfig on the local node) The symbol ! means other than in clustered ontap i.e. storage aggregate show -state !online (show all aggregates that are not online) node run -node -command sysstat -c 10 -x 3 (Running the sysstat performance tool with cluster mode) system node image show (Show the running Data Ontap versions and which is the default boot) dashboard performance show (Shows a summary of cluster performance including interconnect traffic) node run * environment shelf (Shows information about the Shelves Connected including Model Number) DIAGNOSTICS USER CLUSTERED ONTAP Netapp Cluster mode commands ch...
Read more

CIFS shares creation in 7 - Mode

CIFS shares creation Introduction- We can access NetApp volume using CIFS/SMB just like windows share. It is very useful to use NetApp storage in mixed environment of Linux/Windows or on Windows based Products. Step 1) Creating NetApp volume or use Qtree First we need to create  “/vol/mycifs_share” netapp volume or you can use qtree as well. Step 2) Change Secuirty style to NTFS Netapp> qtree security /vol/mycifs_share ntfs Mon Nov 02 06:19:08 EDT [Netapp: wafl.quota.sec.change:notice]: security style for /vol/mycifs_share/ changed from unix to ntfs Step 3) Creating CIFS/Windows Share I assume that NetApp filer has been joined to AD (Active Directory, LDAP) and CIFS licensed is installed/configured and cifs service is  running on NetApp. Now we will create CIFS share and give permissions to User/Groups… Netapp> cifs  shares  -add MyShare /vol/mycifs_share -comment “My Test Windows CIFS Share” The share name ‘MyShare’ will not be accessible by s...
Read more

Creating LUNs and mapping igroups ( 7 Mode & C - mode )

Setting up LUNs and igroups using individual commands -  ( 7 Mode ) Instead of using LUN setup, you can use individual commands to create LUNs, create igroups, and map the LUNs to the appropriate igroups. Before you begin The LUN type must be specified. About this task After the LUN is created, you cannot modify the LUN host operating system type. Note: You can grow a LUN to approximately 10 times its original size. For example, if you create a 10 GB LUN, you can grow that LUN to approximately 100 GB. However, you cannot exceed 16 TB, which is the approximate maximum size of a LUN. Steps Create a space-reserved LUN by entering the following command on the storage system command line: lun create -s size -t ostype   lun_path -s   size indicates the size of the LUN to be created, in bytes by default. -t   ostype indicates the LUN type. The LUN type refers to the operating system type, which determines the geometry used to store da...
Read more